[ltp] T21 +Linksys WPC45G + acx111 +Fedora 4
Efthym
linux-thinkpad@linux-thinkpad.org
Thu, 18 Aug 2005 11:30:01 +0300
here is my dmesg. I keep getting an error "Polling for an IRQ FAILED with
0, cmd_status 0, irqs_active 1, irq_status 0. Bailing."
Any suggestions?
Linux version 2.6.12-1.1398_FC4 (bhcompile@tweety.build.redhat.com) (gcc
version 4.0.0 20050519 (Red Hat 4.0.0-8)) #1 Fri Jul 15 00:52:32 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fffec00 (ACPI data)
BIOS-e820: 000000000fffec00 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7120
ACPI: RSDT (v001 PTLTD RSDT 0x06041160 LTP 0x00000000) @ 0x0fff4c5d
ACPI: FADT (v001 IBM TP-T21 0x06041160 0x00000000) @ 0x0fffeb65
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06041160 LTP 0x00000001) @ 0x0fffebd9
ACPI: DSDT (v001 IBM TP-T21 0x06041160 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 10000000 (gap: 10000000:eff80000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/1 floppy=thinkpad
Initializing CPU#0
CPU 0 irqstacks, hard=c0454000 soft=c0453000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 796.734 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254136k/262080k available (2508k kernel code, 7308k reserved, 684k
data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay loop... 1581.05 BogoMIPS (lpj=790528)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs... it is
Freeing initrd memory: 1083k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PSER] (off)
ACPI: Power Resource [PSIO] (on)
ACPI: Embedded Controller [EC] (gpe 9)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:01: ioport range 0x1000-0x103f could not be reserved
pnp: 00:01: ioport range 0x1040-0x104f has been reserved
pnp: 00:01: ioport range 0xfe00-0xfe0f has been reserved
pnp: 00:08: ioport range 0x15e0-0x15ef has been reserved
Simple Boot Flag at 0x35 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1124360852.245:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 57652F2F3358E32D
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Limiting direct PCI/PCI transfers.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (39 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
pnp: Device 00:0b activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 11 (level, low)
-> IRQ 11
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HITACHI_DK23CA-30, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HITACHI DVD-ROM GD-S200, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
LID SLPB PCI0 USB UART
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 184k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PS/2 Generic Mouse on isa0060/serio1
security: 3 users, 6 roles, 827 types, 100 bools
security: 55 classes, 196759 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses genfs_contexts
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses
genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 11 (level, low)
-> IRQ 11
e100: eth0: e100_probe: addr 0xe8120000, irq 11, MAC addr 00:03:47:BB:B3:01
snd_cs46xx: Unknown parameter `'
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low)
-> IRQ 11
gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1807kHz
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: IBM Laptop detected; this module may corrupt
your serial eeprom! Refusing to load module!
piix4_smbus: probe of 0000:00:07.3 failed with error -1
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
USB Universal Host Controller Interface driver v2.2
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001860
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low)
-> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKB] -> GSI 11 (level, low)
-> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000020
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
acx100: It looks like you've been coaxed into buying a wireless network
card
acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
acx100: You should better have bought e.g. a PRISM(R) chipset based card,
acx100: since that would mean REAL vendor Linux support.
acx100: Given this info, it's evident that this driver is still
EXPERIMENTAL,
acx100: thus your mileage may vary. Reading README file and/or Craig's
HOWTO is
recommended, visit http://acx100.sf.net in case of further
questions/discussion.
acx100: Compiled to use 32bit I/O access (faster, however I/O timing
issues might occur, such as non-working firmware upload!) instead of 16bit
access
Running on a little-endian CPU
acx_init_module: dev_info is: TI acx_pci
acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting
for cards to probe...
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKB] -> GSI 11 (level, low)
-> IRQ 11
PCI: Setting latency timer of device 0000:06:00.0 to 64
acx_probe_pci: WARNING: ACX111 support is quite experimental!
Found ACX111-based wireless network card at 0000:06:00.0, irq:11,
phymem1:0x10c20000, phymem2:0x10c00000, mem1:0xd0974000, mem1_size:8192,
mem2:0xd0a40000, mem2_size:131072
initial debug setting is 0x001b
acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
hw_unavailable = 1
acx_probe_pci: TI acx_pci: Using IRQ 11
reset hw_unavailable++
acx_reset_mac: enable soft reset...
acx_reset_mac: disable soft reset and go to init mode...
Requesting firmware image 'TIACX111.BIN'
No firmware image was provided. Check your hotplug scripts
Attention: no firmware directory specified via module parameter
firmware_dir, using default firmware directory /usr/share/acx
Reading firmware image '/usr/share/acx/TIACX111.BIN'
Allocated 62772 bytes for firmware module loading.
not using auto increment for firmware loading
acx_write_fw: firmware written
acx_write_fw (firmware): 0, acx_validate_fw: 0
acx_reset_dev: boot up eCPU and wait for complete...
EXT3 FS on hda2, internal journal
acx_reset_dev: Received signal that card is ready to be configured :) (the
eCPU has woken up)
acx_reset_dev: Clean up cmd mailbox access area
reset hw_unavailable--
acx100: allocated net device wlan0, driver compiled against wireless
extensions v17 and Linux 2.6.12-1.1398_FC4
******************************************
************* acx_init_mac_1 *************
******************************************
==> Get the mailbox pointers from the scratch pad registers
CmdMailboxOffset = 1dd00
InfoMailboxOffset = 1de86
<== Get the mailbox pointers from the scratch pad registers
CommandParameters = [ 0xd0a5dd04 ]
InfoParameters = [ 0xd0a5de8a ]
Requesting firmware image 'RADIO16.BIN'
No firmware image was provided. Check your hotplug scripts
Reading firmware image '/usr/share/acx/RADIO16.BIN'
Allocated 7208 bytes for firmware module loading.
not using auto increment for firmware loading
acx_write_fw: firmware written
acx_write_fw (radio): 0, acx_validate_fw: 0
acx_issue_cmd FAILED: Invalid parameter [119994850 uSec] Cmd: 18h, Result:
Eh
acx111_init_packet_templates: Init max packet templates
acx111_create_dma_regions: set up acx111 queue memory configuration (queue
configs + descriptors)
dump queue head (from card):
len: 24
tx_memory_block_address: 17F60
rx_memory_block_address: 11660
rx1_queue address: FA54
tx1_queue address: 100D4
get_mask 0x00004182, set_mask 0x00000000
Don't know how to get sensitivity for radio type 0x16, please try to add
that!
Got sensitivity value 0
Got antenna value 0x8F
Got regulatory domain 0x10
get_mask 0x00000000, set_mask 0x00000000 - after update
new ratevector: 82 84 0b 0c 12 16 18 24 2c 30 48 60 6c
setting RXconfig to 2000:0000
Beacon length:69
hw_unavailable--
acx100: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x16 (Radia),
EEPROM version 0x05. Uploaded firmware 'Rev 0.1.0.11' (0x03010101).
creating /proc entry driver/acx_wlan0
creating /proc entry driver/acx_wlan0_diag
creating /proc entry driver/acx_wlan0_eeprom
creating /proc entry driver/acx_wlan0_phy
acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 loaded successfully
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 793792k swap on /dev/hda3. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
genfs_contexts